This adaptor plate and gasket kit allows you to use an 05-newer Slot Style MAF sensor with a JLT Next Generation 12" High Boost intake.

Modification to the JLT tube is required - enlarging the hole

Tuning required

Includes mounting screws for plate to tube and MAF to plate, as well as a gasket.

JLT 03-04 Cobra NEXTGEN CAI to 12" High Boost Conversion Kit

Everything you need to convert your "Next Generation" JLT Cold Air Intake part# CAI2-FMC-0304 into a JLT 12" High Boost Intake part#CAI2-12-FMC-0304.
Requires SCT BA2600 or BA3000 MAF sensor. Optional to purchase below.
Drill out the plug in the molded in MAF housing and install the SCT MAF sensor. See video instructions below

KIT INCLUDES:
4.5X12" S&B Powerstack Air Filter
Custom Rubber MAF Gasket
(2) M4x16 MAF screws

WILL NOT WORK ON ORIGINAL JLT CAI

JLT 03-04 Cobra NEXTGEN 12" High Boost Cold Air Intake Kit

NEW TUBE DESIGN
Using the original JLT CAI as a guide, we molded, sculpted and perfected everything until we had the best looking, fitting and performing system you can buy.
The new JLT tube is 4 1/4" ID, roto molded ABS plastic to resist engine heat and keep the intake air charge nice and cool. NO METAL TUBING HERE!!
Our massive 4.5X12” S&B Powerstacked Air Filter is moved into fender well for a cooler intake charge and can support 800-900 RWHP

MOLDED IN MAF
SCT BA2600 or BA3000 REQUIRED with this kit, optional to purchase below.
Will not work with stock Ford MAF.
Using the supplied MAF gasket and screws install your SCT electronics into the JLT tube and you now have a 105mm MAF incorporated right into the tube. No couplers, reducers or smaller MAF housing to disrupt airflow. Now you have a perfectly smooth, huge 4 ¼” ID tube rushing cool air to the throttle body.
Custom Tuning Required

FINISH OPTIONS
Standard finish is an OEM looking black textured plastic and also available in your cars exact body color. All tubes go through an in-depth process to remove all the texture, then we use only the best quality materials to give each tube a smooth gloss finish.

EASY INSTALL
The new design, detailed instructions and online video instructions helps make this an easy install.

KIT INCLUDES:
•JLT plastic intake tube
•Silicone Coupler
•Apron Plate
•4.5x12” S&B powerstack air filter
•JLT MAF gasket
•HD Clamps & all needed hardware

REQUIRED
SCT BA 2600 or BA300 MAF sensor.
Custom Tuning.

Will not fit with most strut tower braces.

MAINTENANCE
To properly clean your filter, we recommend the S&B Precision Cleaning & Oiling Kit.

*The air filter is low in the bumper to get the coolest air possible. While driving in the rain is not an issue, you MUST be aware of flooded streets and deep puddles. *

JLT 03-04 Cobra NEXTGEN Cold Air Intake Kit

NEW TUBE DESIGN
Using the original JLT CAI as a guide, we molded, sculpted and perfected everything until we had the best looking, fitting and performing system you can buy. The new JLT tube is 4 1/4" ID, roto molded ABS plastic to resist engine heat and keep the intake air charge nice and cool. NO METAL TUBING HERE!!
MAF and filter relocated into fender well for a cooler intake charge and can support 550-600 RWHP

MOLDED IN MAF
The best part of this new JLT Cold Air is we kicked the cool factor up a notch and molded a 105mm MAF housing right in the tube. Now you have a kit you can grow into and not have to buy a complete new kit when you reach 550-600 RWHP. Putting a Whipple or Kenne Bell blower on your 03, 04 Cobra? Simply drill out the pre molded plug on the MAF block located on the bottom of the tube, discreetly out of sight. Install your SCT MAF sensor electronics, add our huge 4.5 X 12” S&B Powerstack filter and you’ve now changed your JLT Cold Air Intake into a JLT High Boost 12” Intake. Molding the MAF into the tube makes for a much smoother air flow with no couplers, reducers or separate MAF housing and can support 800+RWHP for only the cost of the 12” upgrade kit, $60.00.

GAINS
26-30 RWHP are typical with this kit.

FINISH OPTIONS
Standard finish is an OEM looking black textured plastic and also available in your cars exact body color. All tubes go through an in-depth process to remove all the texture, then we use only the best quality materials to give each tube a smooth gloss finish.

EASY INSTALL
The new design, detailed instructions and online video instructions helps make this an easy install.

KIT INCLUDES:
•JLT plastic intake tube
•Silicone Coupler
•Silicone reducer
•Apron Plate
•4x9 S&B powerstack air filter
•MAF adapter
•MAF adapter gasket
•HD Clamps & all needed hardware

Will not fit with most strut tower braces.

MAINTENANCE

To properly clean your filter, we recommend the S&B Precision Cleaning & Oiling Kit.