Torque Solution Throttle Body Spacer (Black): Ford Mustang Ecoboost Turbo 2015+ - TS-TBS-033

PROPOSITION 65

Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

WARNING: Cancer and Reproductive Harm. (http://www.p65warnings.ca.gov)

Learn More

Ford Racing Mustang 5.0L 90mm Throttle Body Adapter (Boss Intake)

 

• Fits 2012 Mustang Boss 302 or Mustang GT with Ford Racing Mustang Boss 302 Intake Manifold M-9424-M50BR.  
• Spacer used to adapt 90MM Billet Aluminum Throttle Body, M-9926-M5090, to 2012 Boss 302 Intake M-9424-M50BR
  

Learn More

Ford Racing Mustang 5.0L 90mm Throttle Body

 

• Fits Mustang GT/Boss 302 with stock 80mm throttle body
  
• Ford Racing's performance electronic throttle bodies are for vehicles equipped with electronic throttle control (ETC)
  
• Electronic throttle control was introduced on the Mustang in 2005. It's introduction has made attention to detail and setup of replacement throttle bodies even more critical than in the past. 
• Includes jumper harness 
  
• Calibration required (not included)
  

All Ford Racing ETC throttle bodies feature:

• All factory sensors installed - no need to tear apart your original throttle body
• Calibrated for consistent idle using the same equipment and procedure as production throttle bodies
• The only throttle bodies backed by Ford Racing and features the Ford Racing logo CNC cut into the TB housing 
• Precision billet construction with tapered inlet for consistent high flow
• Validation through hundreds of hours of dyno, racing, and street performance driving
• Polished aluminum for great looks 
  

Requires:

Adapter: M-9474-M50 for OEM Mustang GT 5.0L 4V TiVCT intake

Adapter: M-9474-M50B for Ford Racing Boss intake M-9424-M50BR

Notes: 

Adapter M-9474-M50 rotates throttle body approximately 15% counter clockwise

Engine cover M-9680-M50 covers throttle body on 5.0L 4V Ti-VCT intake

Boss intake M-9424-M50BR can be port matched to accept throttle body without adapter, requires custom gasket/RTV

Learn More

Steeda 5.0L V8 Coyote Mustang Billet Throttle Body Spacer (2011-2018) - 555-3225

Product Benefits:

• No Tune Required
• Billet Aluminum Construction
• Increase Plenum Volume
• Increases Horsepower and Fuel Mileage
• Simple Bolt-on Design
• Lifetime Warranty

Steeda designed and manufactured this billet aluminum throttle body spacer in-house for the 2011+ Mustang with the 5.0 liter 4V Ti-VCT V8 Coyote modular engine. Made from Billet 6061 aluminum it is designed to create more plenum volume for increased horsepower and better performance from your Pony. The swirl design helps promote airflow by breaking the surface tension of the incoming air.

As an easy bolt-on upgrade for your S197 or S550 Mustang GT, this throttle body spacer will increase horsepower and fuel mileage for a better driving experience. The kit includes instructions, gasket, and mounting hardware. This product is covered with Steeda's signature lifetime warranty.

Note: Will not fit the Bullitt or Mach 1.

Learn More

Finally, an affordable Coyote intake manifold that also performs! The Hi-Ram and Ultra Lo-Ram are designed to fit stock bolt pattern OE heads found on the 2011-2023 Ford 5.0 Coyotes and related engine families, such as, Voodoo and Predators. These kits include fuel rails for use with OEM type fuel injectors and clips, mounting hardware, and O-ring gaskets. Offered in black and natural as-cast finish, both manifolds have a 9.20-inch runner length and are designed to improve the mid to high RPM powerband.
The Ultra Lo-Ram provides an additional 19.4mm front and 42.6mm rear clearance compared to the Ford Performance Cobra Jet manifold, plus clears 2015-2023 Mustang factory hoods. Offered in both round and oval throttle body configurations, with replacement front inlets for easy interchangeability. The oval inlet can accommodate up to a 150x66mm single throttle body and 93mm on the round variant. Round inlets include standard mounting provisions for GT350, GT500, and LS 4-bolt throttle bodies. 2011-2023 GT throttle bodies can be used with the optional 717-18 adaptor.

The aggressively designed Hi-Ram is constructed in a two-piece design to accommodate for air to water intercoolers and feature up to 20% more plenum volume versus Ultra Lo Rams. This manifold design is only offered in an oval throttle body configuration.

Features:
As-cast aluminum construction: more durable for boosted applications, can be welded for modifications
Modular design: accessible runner entries for porting, allows accessories like intercoolers and nitrous plates
300-911 and 300-912 Ultra Lo-Ram will fit under stock hood with stock engine mounts in 2015-23 Mustang
Refined port design with streamlined injector boss for reduced turbulence without loss of flow area
Allows a variety of throttle valves including large monoblade, 2015-20 GT350, 2007-14 GT500, 2019-23 GT500, GM LS 4 bolt, 2011-23 Ford Mustang GT (with optional adapter PN 717-18)
Fuel rails with -8AN ports and dual 1/8 NPT accessory ports for gauges or Gen 3 direct injection fuel line hookup
300-911 and 300-912 front inlets can be interchanged between round and oval with service parts
Plenum Volumes: 300-910 9.8-liters, 300-911 8.4-liters, 300-912 8.2-liters
Two 1/8 NPT ports on all manifolds. Two 3/8 NPT ports on all manifolds, except 300-911 has oneLearn More

Torque Solution Throttle Body Spacer (Silver): Ford Mustang GT 5.0L 2011-2016 - TS-TBS-032

PROPOSITION 65

Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

WARNING: Cancer and Reproductive Harm. (http://www.p65warnings.ca.gov)

Learn More

Torque Solution Throttle Body Spacer (Red): Ford Mustang GT 5.0L 2011-2016 - TS-TBS-032R

PROPOSITION 65

Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

WARNING: Cancer and Reproductive Harm. (http://www.p65warnings.ca.gov)

Learn More

Absolutely MASSIVE VMP 173mm Monoblade Throttle body!

Proprietary bolt pattern to fit the 2007-2014 Shelby GT500 / 2011-2014 5.0L Coyote Mustang, designed to move all the air and make all the power! Works on GT500 and Coyote platforms. Can be used on VMP Gen2-R blowers with the use of a VMP Performance throttle body adapter plate. This throttle body is meant for Race purposes and is best suited for built engines with aftermarket camshafts.

Requires Adapter plate

Tuning required. 160mm and 173mm pictured. Product is one throttle body.

Learn More