You have no items in your shopping cart.
Recon 99-04 License Plate Bulbs / 05-13 Mustang LED Dome Lights (Red- Set of 2)
DOES NOT WORK WITH CARS THAT USE REMOTE START!
Sold as a pair
All new at Lethal Performance for your Mustang is the Recon RED LED Dome Light replacement bulbs for all 05-13 Mustangs and 99-04 Mustang License Plate Bulbs. The Recon Dome LED lights are a direct replacement and can be installed in less than 5 minutes. Get rid of the stock yellow looking interior light and replace it with a nice White LED. We were very impressed with how much of an improvement they made on the LethalGT500.
The new LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.
NOTE: LED's require a resistor or they will have a slight glow to them after the vehicle is turned off. However the current that is drawn to create the glowing bulb is not enough to drain your battery.
Installation Video
Learn MoreRecon 05-09 Mustang LED Brake/Tail Light (13 L.E.D.’s) 360 Degree WHITE
RECON's New LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.
LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the flash rate of the turn signals, some turn on a bad bulb indicator. This can be remedied with our Load Resistors wired across the turn signal bulbs to simulate a filament bulb load.
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. This LED Load Resistor can be use with most signal or brake light which uses SINGLE or DUAL FILAMENT LED light bulbs, like the 7443, 1157, 3157, 4157, 1156, 7440, 3156 etc.
CONNECTION INSTRUCTIONS:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake hot wire. Splice taps allow for installation without cutting your turn signal wires.
Automotive LED Light Bulb Load Resistor Features:
-- Solve LED related turn signal problems such as hyper flashing or burnt out bulb indications.
-- Compact design for easy installation.
-- 6 Ohm 50 Watt resistors can be use will most import and domestic vehicles.
Don't get caught in the dark again...Light It Up With RECON!!!!!
***ATTENTION - VERY IMPORTANT MESSAGE BELOW***
These bulbs are sold individually which means only 1 bulb comes in each package. This means if you need a total of 4 bulbs, you must enter a qty of 4 before clicking the "add to cart" button.
Trunk lights are used in the trunk or cargo area to illuminate the space at night. From the factory, the bulbs are incandescent, lighting up in a yellowish color. By changing the factory bulb to an LED, you can illuminate the area with a much brighter light, and add a pure white, luxury look. The installation is 100% plug-and-play, just replace your factory bulb.
BULB DESIGNFitment. All bulbs use a standard 31mm terminal, with aluminum contacts, designed for exact replacement of your factory 31mm festoon bulb. Just remove the old bulb, and plug in the new LED.
PLEASE NOTE: SMD12 Board is an LED board, which may mount to the exterior of your trunk light housing. FlexLight is an LED strip, which plugs into your factory trunk light socket, and mounts directly into your trunk area using included adhesive strips or velcro. If you would like a direct replacement bulb, we recommend SMF2 or SMF6. We offer SMD12 Board and FlexLight for those who want to maximize brightness.
Included in your order is ONE BULB.
Learn MoreMap lights, or the pair of lights above your front seats, use incandescent bulbs from the factory, giving them a yellowish color. By replacing these factory bulbs with LEDs, you can add a luxurious and modern look to your vehicle, with a cool white color, just like the map lights on newer luxury vehicles. You can also increase the brightness with SMD5 or SMD9 bulbs, to improve the performance of your map lights. The installation is 100% plug-and-play, just replace your factory bulb!
BULB DESIGNIncluded in your order is TWO BULBS.
Learn MoreFog Light LED bulbs are an excellent way to improve the appearance of your vehicle. From the factory, most vehicles come with halogen bulbs, which project in a yellowish light. By replacing them with LEDs, you can create a modern appearance with the cool white light of LEDs. The installation is 100% plug-and-play, just replace your factory bulb!
Please note: Fog Light LEDs are primarily for cosmetic upgrade. Some models may not provide an increase in output.
BULB DESIGNIncluded in your order is TWO BULBS.
Learn MoreDiode Dynamics is proud to introduce a revolutionary new product: PRISM Multicolor LED bulbs, for direct replacement in any fog light or DRL application. By using an RGB controller, you can set them to any color imaginable, or use any lighting mode offered by the controller.
The bulbs utilize bright 5050-size SMD chips, and are designed to be a direct replacement for the factory bulb, with OEM-size sockets. The bulbs have been tested for reliability over time, with an expected life of 40,000 hours.
This is an exclusive product, designed and developed by Diode Dynamics LLC.
Installation:
The whole system is 100% plug-and-play. No cutting, no ballasts, no wiring to your battery. Here's how to install:
Remove your factory bulb, and replace it with the PRISM bulb.Included in your order:
- Two PRISM RGB Multicolor bulbsYou must use an RGB controller to power and control the bulbs. The bulbs use a standard 4-pin connector, with a common positive (+) wire.
These bulbs are compatible with all other Diode Dynamics RGB products, such as our RGB controllers, RGB 2-way splitters, and RGB extension wires.
All Diode Dynamics RGB controllers come with four (4) RGB outputs. For example, if you would like to purchase a set of PRISM bulbs for your fog lights and DRLs, you would just need one controller. If you already have an RGB controller for your footwell lighting, you can simply add these to that controller if you'd like. Keep in mind that all RGB lights on one controller will work together.
Please note: We recommend a fog light application. If you install in a DRL/high beam application, the LEDs will still turn on as your high beams, but will not project as much light as the factory light. This product is intended for its cosmetic upgrade benefits.
Learn MoreFrom the factory, rear turn signal bulbs are powered by standard incandescent lights that light up white in color, and cast light through your red or amber tail light lens. This results in a washed-out color. Newer luxury vehicles are using LEDs for turn signals, because LEDs offer a crisp, instant on/off function, increased brightness, and true, vibrant color. By replacing the bulbs in your vehicle, you can achieve this modern look! The installation is 100% plug-and-play, just replace your factory bulb. The bulb may blink faster since it uses less power, and your vehicle thinks the bulb is out- to fix this, please see "hyperblinking" section below.
BULB DESIGNFitment. All three bulbs use a quality inject-molded 3157 terminal, with a full-size base connector and proper pin alignment, designed for exact replacement of your factory 3157 bulb.
Included in your order is SIX BULBS.
Learn MoreWhen you replace incandescent turn signal bulbs with LEDs in most vehicles, the vehicle will start hyper-blinking because the LED uses much less power, and the vehicle thinks the bulb is out. You can use these resistors to fix the problem of hyperblinking when you convert to LED bulbs.
Diode Dynamics resistors have extra-long 8" leads for easier installation, and have a rating of 50w, 6ohm. This is usually enough to compensate for one bulb. If you are installing four LED turn signals (front and rear) we recommend four total resistors.
Included with your order:
2 resistors