Steeda's cold air high-flow intake for the 03-04 Cobra features a reusable dual cone filter with more surface area than single cone models to flow the most air.

The Steeda high velocity air intake features a stainless steel heat shield that seals against the hood shielding more of the air from the engine compartment heat than the competitions models.

This intake is good for 14 to 18 RWHP on a stock Cobra and has been dyno tested in our Pompano Beach facility to add up to 25 RWHP on a modified Cobra.

All the necessary hardware is included for a direct bolt-on installation. Used in cars exceeding 600 rear wheel horsepower!

Read more about the advantages in Steeda Mustang Cold Air Intakes over the competitors on our blog: https://www.steedablog.com/2012/03/mustang-cold-air-intake-truth/

Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.

Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.

The new 2016 MK3 Ford Focus RS is a fantastic performance platform that while already very good, can still be taken to the next level. Take the intake system of your 2.3L EcoBoost Focus RS to the next level with our in-house designed, tested, and manufactured Steeda Focus RS Cold Air Intake.

This Steeda Focus RS Cold Air Intake for the 2016 Focus RS does not require any ECM tuning making it an easy direct bolt-on. With peak to peak gains of 10 horsepower at the wheels and max gains of up to 16 horsepower, these are performance gains you will definitely feel. Our system incorporates a roto-molded thermoplastic airbox with a thermoplastic velocity stack, a high-flow serviceable air filter, and a silicone intake tube.

Better intake temperatures. The Steeda cold air intake gives your Mk3 Focus RS better intake air temperatures, this results in better performance and improved fuel economy. The lower IATs are a result of the design of the airbox, high flow filter, and the precision-molded thermoplastic velocity stack. The airbox was designed to utilize the cold air feed coming from the grille while sealing directly to the hood liner to ensure a cool, dense air charge to the engine. 

Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.

Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.

Steeda's high flow air intake for the 2.3L and 2.5L Fusion is like 2 intakes in one all-inclusive kit!

Our high flow cold air intake includes an insert allowing you to use it as a direct bolt on intake kit with no tuning required or remove the insert to for even more airflow and combine it with a custom tune for THE most powerful kit on the market for your Fusion.

Steeda's high flow intake also features a stainless steel heat shield and high flow cone-style air filter for great airflow and low intake air inlet temperatures and improved gas mileage.

Gain of up to 8hp and 10ft/lbs of torque are possible with the insert in place. More to be had with no insert and custom tuning.

Fitment Note: Not compatible will hybrid models.

Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.

Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.

The MK3 2013-2018 Ford Focus ST is a fantastic performance platform that while already very good, can still be taken to the next level. Take the intake system of your 2.0L EcoBoost Focus ST to the next level with our in-house designed, tested, and manufactured Steeda Focus ST Cold Air Intake.

This Steeda Focus ST Cold Air Intake for 2013-2016 Focus ST does not require any ECM tuning making it an easy direct bolt on. With peak to peak gains of 10 horsepower at the wheels and max gains of up to 16 horsepower, these are performance gains you will definitely feel. Our system incorporates a roto-molded thermoplastic airbox, a precision-molded thermoplastic velocity stack, a high-flow serviceable air filter, and a silicone intake tube.

Lower IATs. The Steeda cold air intake gives your Mk3 Focus better intake air temperatures, this results in better performance and improved fuel economy. The lower IATs are a result of the design of the airbox, high flow filter, and the precision-molded thermoplastic velocity stack. The airbox was designed to utilize the cold air feed coming from the grille while sealing directly to the hood liner to ensure a cool, dense air charge to the engine. 

A suggested add-on is Steeda's Focus ST Ram Air Intake Scoop for 13-18 ST.

Purchase your Steeda Focus ST Cold Air Intake for your 20132018 Focus ST at Steeda Autosports today!

Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.

Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.

Increase horsepower and torque with our high velocity cold air intake for your 2005-09 4.0L V6 Mustang.

Steeda's high velocity cold air intake earns it's name due to the exclusive velocity stack design.

The radiused entry of the velocity stack design increases and straightens airflow into the mass air for greater power and a cleaner MAF signal.

With a clean MAF signal you get better drivability than other designs and makes it easier to tune resulting in better power and the best drivability possible.

Includes a serviceable lifetime dual cone air filter that can be cleaned and re-oiled, but the big news here is that we've streamlined the airflow in the V6 S197 Mustang to the point that a computer re-flash isn't just an option, it's required! Check out the SCT X4 - the perfect tool for the job!

Steeda's intake is supplied with a stainless steel air box and CNC billet aluminum mass air meter. It mounts in the factory location with the supplied rubber trim to seal it against the hood & fender to keep the hot air isolated from the filter. Our tests showed inlet temps a mere 10 degrees above ambient temperature. The Steeda Lifetime Filter can easily be cleaned and re-oiled, making maintenance a snap. All hardware required for installation is included in the kit.

We've found between 16 -20 more rear wheel horsepower with this kit combined with the required SCT tune. Power you can feel!

Read more about the advantages in Steeda Mustang Cold Air Intakes over the competitors on our blog: https://www.steedablog.com/2012/03/mustang-cold-air-intake-truth/

Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.

Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.

This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.