Please Note: Does not work on Cobra models, which require custom calibration.

Cobra calibrated meters can be special ordered. Please call for details. 

Learn More

Please Note: Does not work on Cobra models, which require custom calibration.

Cobra calibrated meters can be special ordered. Please call for details. 

Learn More

Please Note: Does not work on Cobra models, which require custom calibration.

Cobra calibrated meters can be special ordered. Please call for details. 

Learn More

Our aluminum flange allows the 05+ sensor to be installed directly onto any size tube. The flange must be attached by welding. The radius on the flange is cut for 3.5", but welding will fill in any small gaps present when used on other tube sizes.

If you are not able to weld the flanges on take a look at our billet MAF housings.

In 2005 Ford Introduced a new style of mass-air sensor. It is commonly referred to "slot" or "card" style. This sensor has no housing, the stock airbox has a receptacle for the sensor.

We have found that the new sensor works very well in blow-through applications. Blow-through means that the mass air sensor is placed after the compressor (supercharged or turbocharged vehicles). The slot style MAF provides a very clean and consistent signal when used in blow-through. The slot style MAF can be placed in any size tube, from 3" to 4.5". We do not recommend going smaller than 2.75". In blow-through applications a 3" tube will result in the best signal, 3.5" tube will result in a marginal signal, and 4" will result in a very poor signal when used in blow-through. The car will need to be properly tuned for the new MAF sensor housing size.

When it comes to driveability and throttle response, blow through with an 05+ MAF is the best way to go. Having the MAF sensor far away from the engine makes the car harder to tune and hinders throttle response. In the past tuners used to recommend suck-through, but this has since changed with the introduction of the 05+ MAF. With blow-through the by-pass valve can now be vented to atmosphere, this will reduced air temps, because the air is no longer being re-circulated and re-heated.

Running the MAF sensor in blow through in a smaller tube than stock reduces range, to get this range back you can use a MAFIA extender or an VMP HPX slot style sensor. For very high power applications the VMP HPX sensor is recommended, as the MAFIA can only be used up to setting 3 on the 05+ MAF.

Learn More

This maf is a universal fit for Ford vehicles. Please specify year, model, engine size, and injector size when ordering. Computer tuning is required for 42lb and larger injectors. 05+ style maf connector is required

Learn More

Edelbrock's high flow Mass Air Flow Sensor (MAFS) for GM and Ford applications are the perfect upgrade for any MAFS equipped vehicle with performance upgrades that have elevated air flow above the range of the stock sensor. The Ford sensor #15402 increases the air flow to 113 lbs. per minute. Both kits utilize a large 95mm venturi style housing that reduces air flow restriction and improves the overall horsepower potential. These sensors feature an injection molded housing for OEM level precision with a modern blade-style element for the latest in technology and easy installation on newer vehicles. Match these kits with our conical air filter for the optimal air flow performance upgrade.Learn More

Extended range HPXWill never peg. Sensor will support over 1000HP when installed in a 3" housing.The HPX will support the following horsepower3" housing 840 WHP3.5" housing 1140 WHP80mm or stock 05GT airbox 920 WHP85mm housing 1050 WHP95mm housing 1300 WHP100mm housing 1450 WHP Updated sensor curve has been engineered to maintain perfect idle resolution even when used on vehicles making under 300HP.This sensor can be used in any housing from 2" to over 5". It can also be used for blow-thru or draw-through configurations.Limited lifetime warranty.This is the last mass airflow sensor you will ever buy.*Requires 05+ Ford maf connector*Requires computer tuning*Can be used on any 0-5V maf system with computer tuning*Transfer function generating software tool available for FREE download*Air temp sensor reads 40K ohms at room temphttp://www.pmas-maf.com/resources/hpxait.xlsLearn More

This maf is a 3" universal for use with blow-through applications on Ford vehicles. Please specify year, model, engine size, and injector size when ordering. Computer tuning is required for 42lb and larger injectors. 05+ style maf connector is required

Learn More