Currently Shopping by:
You have no items in your shopping cart.
Recon 05-09 Mustang LED Brake/Tail Light (12 LEDs) WHITE
RECON's New LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.
LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the flash rate of the turn signals, some turn on a bad bulb indicator. This can be remedied with our Load Resistors wired across the turn signal bulbs to simulate a filament bulb load.
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. This LED Load Resistor can be use with most signal or brake light which uses SINGLE or DUAL FILAMENT LED light bulbs, like the 7443, 1157, 3157, 4157, 1156, 7440, 3156 etc.
CONNECTION INSTRUCTIONS:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake hot wire. Splice taps allow for installation without cutting your turn signal wires.
Automotive LED Light Bulb Load Resistor Features:
-- Solve LED related turn signal problems such as hyper flashing or burnt out bulb indications.
-- Compact design for easy installation.
-- 6 Ohm 50 Watt resistors can be use will most import and domestic vehicles.
Don't get caught in the dark again...Light It Up WIth RECON!!!!!
***ATTENTION - VERY IMPORTANT MESSAGE BELOW***
These bulbs are sold individually which means only 1 bulb comes in each package. This means if you need a total of 4 bulbs, you must enter a qty of 4 before clicking the "add to cart".
Recon 05-09 Mustang LED Brake/Tail Light (13 L.E.D.’s) 360 Degree WHITE
RECON's New LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.
LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the flash rate of the turn signals, some turn on a bad bulb indicator. This can be remedied with our Load Resistors wired across the turn signal bulbs to simulate a filament bulb load.
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. This LED Load Resistor can be use with most signal or brake light which uses SINGLE or DUAL FILAMENT LED light bulbs, like the 7443, 1157, 3157, 4157, 1156, 7440, 3156 etc.
CONNECTION INSTRUCTIONS:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake hot wire. Splice taps allow for installation without cutting your turn signal wires.
Automotive LED Light Bulb Load Resistor Features:
-- Solve LED related turn signal problems such as hyper flashing or burnt out bulb indications.
-- Compact design for easy installation.
-- 6 Ohm 50 Watt resistors can be use will most import and domestic vehicles.
Don't get caught in the dark again...Light It Up With RECON!!!!!
***ATTENTION - VERY IMPORTANT MESSAGE BELOW***
These bulbs are sold individually which means only 1 bulb comes in each package. This means if you need a total of 4 bulbs, you must enter a qty of 4 before clicking the "add to cart" button.
FUNCTION: Map lights, or the pair of lights above your front seats, use incandescent bulbs from the factory, giving them a yellowish color. By replacing these factory bulbs with LEDs, you can add a luxurious and modern look to your vehicle, with a cool white color, just like the map lights on newer luxury vehicles. You can also increase the brightness with SMD5 or SMD9 bulbs, to improve the performance of your map lights. The installation is 100% plug-and-play, just replace your factory bulb!
BULB DESIGNIncluded in your order is TWO BULBS.
Learn MoreWhen you replace incandescent turn signal bulbs with LEDs in most vehicles, the vehicle will start hyper-blinking because the LED uses much less power, and the vehicle thinks the bulb is out. You can use these resistors to fix the problem of hyperblinking when you convert to LED bulbs.
Diode Dynamics resistors have extra-long 8" leads for easier installation, and have a rating of 50w, 6ohm. This is usually enough to compensate for one bulb. If you are installing four LED turn signals (front and rear) we recommend four total resistors.
Included with your order:
2 resistors