Recon 99-04 License Plate Bulbs / 05-13 Mustang LED Dome Lights (Red- Set of 2)

 DOES NOT WORK WITH CARS THAT USE REMOTE START!

Sold as a pair

All new at Lethal Performance for your Mustang is the Recon RED LED Dome Light replacement bulbs for all 05-13 Mustangs and 99-04 Mustang License Plate Bulbs. The Recon Dome LED lights are a direct replacement and can be installed in less than 5 minutes. Get rid of the stock yellow looking interior light and replace it with a nice White LED. We were very impressed with how much of an improvement they made on the LethalGT500.

The new LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.

NOTE: LED's require a resistor or they will have a slight glow to them after the vehicle is turned off. However the current that is drawn to create the glowing bulb is not enough to drain your battery.

Installation Video

www.youtube.com/watch

Learn More

Recon 2011-2012 Mustang White LED Replacement Reverse Lights (Set of 2)

NOTE: 2011-2012 Mustang GT and GT500's require (4) bulbs total. So you must add (2) packs of these bulbs to your cart in order to have enough bulbs to complete the install.

**RESISTORS MAY BE NEEDED TO KEEP THE BULB FROM GLOWING ONCE THE VEHICLE IS SHUT OFF**

All new at Lethal Performance are the Recon LED replacement reverse lights kits. The package includes 2 high quality LED bulbs which are a direct replacement for your stock reverse light bulb. Each bulb has 9 LED's. Just unscrew the 3 nuts that hold your tail light in place, remove the old bulb and put the new one it. It's that easy. The new LED bulb will get rid of that yellow looking bulb and replace it with a brighter and cleaner looking LED bulb which has a clear illumination to it. You'll be very impressed once you see how much these improve the look of your car and you'll be even more impressed when you see how awesome the car looks at night.

The new LED Bulbs Feature extremely low power consumption,  generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.

Learn More

Recon 99-04 Mustang License Plate Bulbs / 05-12 Mustang LED Dome Lights (White-Set of 2)

Sold as a pair

All new at Lethal Performance for your Mustang is the Recon White LED Dome Light replacement bulbs for 05-12 Mustangs. These can also be used on all 99-04 Mustangs as license plate bulbs. The Recon Dome LED lights are a direct replacement and can be installed in less than 5 minutes. Get rid of the stock yellow looking interior light and replace it with a nice White LED. We were very impressed with how much of an improvement they made on the LethalGT500.

The new LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.

NOTE: LED's require a resistor or they will have a slight glow to them after the vehicle is turned off. However the current that is drawn to create the glowing bulb is not enough to drain your battery.

Installation Video

www.youtube.com/watch

Learn More

Recon LED Bulb Resistor Kit (1 Piece)

We have found that most 2011 model years will require a resistor to be installed in order for the LED reverse light to function properly. This is due to the newer computers which run the vehicles lightning system. The LED's require lower voltage to run them which the computer thinks is a blown bulb. The resistor will in turn stimulate a load signal similar to that of a standard filament bulb.



LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the flash rate of the turn signals, some turn on a bad bulb indicator. This can be remedied with our Load Resistors wired across the turn signal bulbs to simulate a filament bulb load.

This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. This LED Load Resistor can be use with most signal or brake light which uses SINGLE or DUAL FILAMENT LED light bulbs, like the 7443, 1157, 3157, 4157, 1156, 7440, 3156 etcLearn More

Recon 2010+ Mustang WHITE LED Licence Plate Bulbs (Pair)

The 2010+ mustang requires 2 bulbs so you only need to order (1) of this part number to complete installation on 1 car.

All new at Lethal Performance for your 2010+ Mustang is the Recon White LED License Place replacement bulbs. The Recon License Plate LED lights are a direct replacement and can be installed in less than 5 minutes. Get rid of the stock yellow looking interior light and replace it with a nice White LED. We were very impressed with how much of an improvement they made on our 2011 5.0L Mustang GT.

The new LED Bulbs Feature extremely low power consumption, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.

Learn More

Recon 194 / 168 High-Power 1-Watt LED Bulbs Wedge Style - AMBER (Two Bulbs Per Package) - 264200AM

194 / 168 High-Power 1-Watt LED Bulbs Wedge Style - AMBER (Two Bulbs Per Package)

Learn More

FUNCTION

Trunk lights are used in the trunk or cargo area to illuminate the space at night. From the factory, the bulbs are incandescent, lighting up in a yellowish color. By changing the factory bulb to an LED, you can illuminate the area with a much brighter light, and add a pure white, luxury look. The installation is 100% plug-and-play, just replace your factory bulb.

BULB DESIGN
SMF2: This bulb has a standard festoon base, with two 5050-size Epistar SMDs and a protective cover for added durability and style.
SMF6: Standard festoon base, with six 5050-size Epistar SMD chips arranged on a rectangular panel.
SMD12 Board: This is an LED panel, fitted with 12 5050-size Epistar SMD chips. Comes with spring-loaded festoon-style adapter for direct installation. Plug the adapter into the bulb socket, then just stick the board in place with the mounting adhesive pad. This may need to be mounted to the exterior of your trunk light housing.
FlexLight: This is a 20-inch, low-profile LED strip, with 30 5050-size Epistar SMD chips. Comes with spring-loaded festoon-style adapter for direct installation. Mounts in your trunk area, flexible and waterproof, for maximum brightness.

Fitment. All bulbs use a standard 31mm terminal, with aluminum contacts, designed for exact replacement of your factory 31mm festoon bulb. Just remove the old bulb, and plug in the new LED.

PLEASE NOTE: SMD12 Board is an LED board, which may mount to the exterior of your trunk light housing. FlexLight is an LED strip, which plugs into your factory trunk light socket, and mounts directly into your trunk area using included adhesive strips or velcro. If you would like a direct replacement bulb, we recommend SMF2 or SMF6. We offer SMD12 Board and FlexLight for those who want to maximize brightness.

Included in your order is ONE BULB.

Learn More

FUNCTION

Map lights, or the pair of lights above your front seats, use incandescent bulbs from the factory, giving them a yellowish color. By replacing these factory bulbs with LEDs, you can add a luxurious and modern look to your vehicle, with a cool white color, just like the map lights on newer luxury vehicles. You can also increase the brightness with SMD5 or SMD9 bulbs, to improve the performance of your map lights. The installation is 100% plug-and-play, just replace your factory bulb!

BULB DESIGN
SMD2: Compact design, with two 5050-size Epistar SMD chips mounted directly to the base connector. Direct replacement, plug and play.
HP3: One high-power SMD under a diffusing lens for truly even output (no hotspots). Constant current design and air-cooled base for superior reliability. Features dual contact pins and nonpolar function for easy installation.

Included in your order is TWO BULBS.

Learn More