CALL 877-2-LETHAL (877-253-8425) or EMAIL // M-F, 9am-6pm
0 Items Cart
My Cart

You have no items in your shopping cart.

Facebook Twitter Rss Pinit Youtube Instagram TeamLethal

JMS Progressive Nitrous Controller

SKU: JMS-NOS6021

Manufacturer: JMS Chip

Be the first to review this product

Availability: In stock

$399.00
Free Shipping on this item!

JMS Progressive Nitrous Controller

*image is only a representation and may not be accurate

The Progressive Nitrous Controller that is designed to out perform!

The JMS Progressive N20 Controller is the new standard for Nitrous Controllers! Finally, there is a N20 Controller that allows for maximum ADJUSTABILITY while combining all of the popular nitrous add-ons into one device. No external relays, triggers or RPM Switches required...it’s all in one device!

  • Easy to setup and use. No relays, triggers, or RPM switches required, everything is built into one unit!
  • Compatible with all 12V or 16V battery systems & one to sixteen cylinder engines.
  • Adjustable Solenoid Frequency
  • Wide-Open Throttle Enable Trigger
  • Dual Independent Ramp Rates

  • SIMPLE INSTALLATION:

    Easy to setup and use. No need for a laptop or complicated user display. All adjustments can be made with the included flat-head screwdriver. Complete Progressive Nitrous System Control in a single unit: eliminate external relays, triggers and RPM switches.

    CASE/ENCLOSURE SPECIFICS AND DIMENSIONS:
    Silver, Aluminum Case with four mounting tabs
    Length: 5 1/2", Width: 2 1/2", Height: 1 1/2"

    OPERATING VOLTAGE RANGE:

    9.5V - 20V DC

    COMPATIBILITY:
    - Works with all 12V or 16V battery systems.
    - Supports all engines from One to Sixteen cylinders, Four Stroke or Two Stroke
    - Automatically functions as a Turbo Nitrous Controller, if the Start Percentage is set higher than the End Percentage.

    INPUTS:
    -RPM: Monitors Engine RPM. Connect to the negative side of the ignition coil or fuel injector.
    -Wide Open Throttle Enable Trigger:
  • Trigger (1) : Ground Enable, typically connected to a micro-switch and grounded at WOT.
  • Trigger (2): 0-5V DC (invertable), typically connected to a Throttle Body TPS.
  • Notes: Either WOT Trigger may be used to enable the controller. The enable voltage must be set by the user.
    -Tire Spin /Gear Lock Out:
  • Ground Enabled: Typically connected to a micro-switch.
  • Depending on when this input is grounded: can either manually lock the controller OFF or can be used to enable a second progressive ramp rate setting.

  • OUTPUTS:
    55amp maximum combined Fuel & Nitrous Solenoid Output
    +12V Timing Retard Output, 50mA, short circuit protected
    ADJUSTABLE SOLENOID FREQUENCY:
    12.5hz, 20hz, 25hz, 40hz (special solenoids are required for 40hz)
    INDEPENDENT FUEL AND NITROUS SOLENOID CONTROL:
    Increased amperage capacity
    Improved solenoid accuracy and control
    FUEL SOLENOID SETTINGS:
    The fuel solenoid output can be independently modified to control activation lean spikes.
    - 100% duty cycle
    - 85% duty cycle for the initial 0.5 seconds after activation and then matches the Nitrous Solenoid Output
    - 75% duty cycle for the initial 0.3 seconds after activation and then matches the Nitrous Solenoid Output

    RPM WINDOW SWITCH:
    Minimum RPM to enable Nitrous Output: 1000 RPM
    Maximum RPM to disable Nitrous Output: 16,900 RPM

    12V TIMING RETARD OUTPUT:
    +12v output when the Nitrous Output is active
    Designed to be connected to an ignition box timing retard input.

    INSTALLATION KIT:

    3 feet of power/solenoid wiring, wiring harness, heat shrink connectors, heat shrink ring terminal, self tapping screws, tie straps

    Manufacturer JMS Chip
    Free Shipping Yes

    Write Your Own Review

    Only registered users can write reviews. Please, log in or register